MASTER CLASS CANDLESTICK "TENDERNESS"

Send

On the basis of a wine glass, 17 cm high, a candle holder is made with flowers from foamiran.

For work we take:
- plastic suede in white and green.
- the glass is transparent.
- any candle.
- scissors.
- a toothpick.
- oil art paints.
- a piece of foam.
- thin wire.
-glue gun.
- thin green paper for creativity.
- a toothpick.
- cardboard.
- paper tape.
- lighter.
- Curling Hair.
- red sequins and decorative heart for decoration.
For convenience in work, we will first draw the templates. Flower petals look like big droplets. Two small sizes 4 x 4 and 5 x 5 cm. In the middle petal 5.5 x 6 cm in size, the upper part has one wave. The largest petal with three waves and its size is 6 x 6.5 cm. The leaves of 3 x 5.5 cm are similar to a boat, but on a leg. Sepals are similar to stars with a diameter of 7 and 5 cm.

On white suede, use a toothpick to pattern large petals of 10 and 14 pieces. Small need 25 and 30 blanks. All neatly cut out.

Next, you need to tint wide edges with these blanks in red. We will use art paints and a piece of foam. It is necessary to process from two sides.

Change the color of all the petals at once.

Now knead the fabric of the petals with your hands, make it soft. We fold each blank with an accordion and scroll with our fingers, and then straighten it again.

And in this way we process all the petals.

And now we will give them a new form. Since foamiran becomes plastic when exposed to heat, we will use a hair curler. On the heated device, apply the middle part of the petal for a few seconds. The workpiece and the curling iron are positioned horizontally. On the warm part of the petal, immediately make a deepening with the thumbs.

And now we place the petal with a recess down and with the help of a lighter we make bends along the edge of the workpiece. Under the influence of heat, suede itself bends to the fire. On large petals we make two bends, leaving the middle wave free.

In the petals a little smaller in size, the same bends, but the medium wave can be turned in any direction.

Now move on to the small petals. The bend will be all over the top edge. You can do this in several steps.

In this way, all the petals have a new shape.

Now take the green suede. According to the template, cut out 2 large and 4 small sepals. And we will immediately process it. Fold all 5 corners of the workpiece together and scroll with your fingers.

But we do not fully disclose, we leave the resulting curves.

It was the turn of the leaves. There will be 8 pieces. Also cut according to the template and with a toothpick draw veins.

Scissors around the edge make small notches. Then we add each sheet in half, vertically and bring the fold to the heat of the curling iron. Then he quickly pressed his fingers.

Now let's start assembling a large rose. We need blanks. The largest 5 and 7 pieces are slightly smaller, 8 parts of the next size and 5 smallest. Need 1 large sepals and a base for a flower on a wire. It was made from paper tape in the shape of a droplet, and the wire was fixed in it with a glue gun.

Let's start with the smallest workpieces. We lubricate the first two petals completely with glue and press them tightly pressed to the base from opposite sides. The remaining 3 blanks are fixed in a circle. Apply glue from below and above the middle.

The next 8 parts must be placed in one row, so we will fix with the imposition of one part on another. We apply glue only until the middle of the workpieces.

In the third row, large petals will begin. There are 7 of them. We have a fan in a circle, but we apply glue only to the bottom of the workpiece. The rose is revealed.

And to glue the largest petals, Turn the flower wire up. And now we have the last 5 petals in one circle. We will only glue on the bottom of the part.

It turns out a lush open rose.

It remains to fix the green sepals.

But in our candlestick there are two big roses.

We still have small petals. We will do more roses. For one, take 3 larger petals and 5 small ones. One base of scotch tape and a green backing.

There will be only two rows. We glue small petals tightly pressed to the base in a circle.

And the remaining 3 parts are glued in a circle for the bottom of the workpiece.

We fix the green part by threading through the wire.

There will be 3 such roses. And another rose will be a little larger than these. Because in the first row there will be 5 petals, and in the second there are 6 blanks and we will fix it inside the glass. But now back to the leaves. Fingers knead tails. We cut the wire 8 cm long and glue the leaves on it for these tails.

Now we collect these leaves in bunches. It will turn out two of 3 blanks and one of two leaves. And with green paper we glue the joints.

Now all the parts are ready for assembly. Two large roses, 3 small, one medium and leaves.

Getting to the assembly. We take a glass, circle the neck twice on cardboard. And we will cut out not along the contour. One circle will be slightly larger than the intended line, and the second less than the markup.

Take a smaller circle and make two small holes in the middle. We insert a medium-sized rose in one hole, and put a double sheet next to it.

We try on the height of the rose by the glass, twist the rest of the wire with a little ring on the wrong side. We bend the wire of the leaf and fix it with a gun.

Then we turn over and decorate on the front side with shiny sequins and a heart.

Then we glue this circle on the second one, which is larger. Lubricate the free edge with glue and glue the glass well. Putting it upside down so that the rose is inside the glass. Now it will be the bottom of the candlestick.

We rise higher to the leg. Here we fix the first big rose. We do not cut the wire, but twist it around the legs and apply hot glue for better fixing.

The second flower will be placed on the opposite side of the legs of the glass and well fixed.

Now take a twig of 3 leaves and glue between the roses. But the top edge of the leaves should touch the former bottom of the glass.

We have the second branch on the other side of the flowers.

But on this side you need to add a small rose while standing. We also glue it well.

There are two small roses left, so we twist the wire with a ring to the sepals.

Apply glues to this twist and press this flower between two large roses, closing all the joints. We attach the second flower in the same way, but on the other side. The candlestick is assembled, it remains to put and light a candle.